Akbar Mohammadi Ajamloo

Multi-physics modelling of additively manufactured electrical machines

Ongoing and Completed Research

Development of Rib-less Interior Permanent Magnet (IPM) Rotor Topology

  • Optimized topology for additive manufacturing
  • Multi-physics analysis

3D Printed Permanent Magnet Rotors (ongoing)

  • Three 3D printed rotor designs
  • Multi-physics analysis

Asymmetric Topology in Permanent Magnet Assisted Synchronous Reluctance Motors (PMaSynRM)

  • Research into optimized design for enhanced machine performance

Development of Test Setup for Rotor Evaluation (ongoing)

  • Development of a test setup for evaluation and validation of the simulation results
  • Evaluation of mechanical and magnetic behavior

Bio

Research Assistant

Motor-drive lab Shahid Behesti University (2019–2023)

Researcher

Niroo Research Institute (2018–2019)

MSc Electrical Machines and Power Electronics

K.N. Toosi University of Technology, Iran (2016–2018)

“Design and analytical modeling of a novel transverse flux permanent magnet (TFPM) generator for direct-drive wind turbine application”

BSC Electrical Engineering

K.N. Toosi University of Technology, Iran (2012–2016)

“Design, simulation and fabrication of a ¼ hp single-phase induction motor”

EMByAM Publications

Design Considerations of a New IPM Rotor With Efficient Utilization of PMs Enabled by Additive Manufacturing

A. M. Ajamloo, M. N. Ibrahim and P. Sergeant, IEEE Access, vol. 12

Design, Modelling and Optimization of a High Power Density Axial Flux SRM with Reduced Torque Ripple for Electric Vehicles

A. M. Ajamloo, M. N. Ibrahim and P. Sergeant, Machines 11, no. 7

A Review on Properties of 3D Printed Magnetic Cores for Electrical Machines: Additive Manufacturing Methods and Materials

A. M. Ajamloo, M. N. Ibrahim and P. Sergeant, ICEM 2024

A New Hybrid Permanent Magnet-Assisted Synchronous Reluctance Motor with Efficient Utilization of Rare-Earth Permanent Magnets

A. M. Ajamloo, A. Ghaheri, M. N. Ibrahim and P. Sergeant, IEEE Transactions on Energy Conversion

Principle of Torque-Axis Alignment in New Asymmetric PM Synchronous Reluctance Machines: Towards Less-Rare-Earth PM Machines

A. M. Ajamloo, A. Ghaheri, M. N. Ibrahim and P. Sergeant, IEEE Transactions on Transportation Electrification, vol. 11

Investigation of Different Pole Configurations in New Asymmetric Permanent Magnet Synchronous Reluctance Machines

A. M. Ajamloo, A. Ghaheri, M. N. Ibrahim and P. Sergeant, IEEE Transactions on Magnetics

Properties of Additively Manufactured Soft and Hard Magnetic Cores for Electrical Machines: Methods and Materials − A Review

A. M. Ajamloo, M. N. Ibrahim and P. Sergeant, IEEE Transactions on Industry Applications

Additively Manufactured Spoke-type Permanent Magnet Rotors: Solutions to Multidisciplinary Design Challenges and Comparison with Traditional Design

A. M. Ajamloo, H. Tiismus, A. Kallaste, M. N. Ibrahim, P. Sergeant, IEEE Transactions on Energy Conversion

A comprehensive investigation of low-cost permanent magnet machines with ferrite magnets and enhanced magnetic loading

A. Mohammadi Ajamloo, F. Desmet, P. Sergeant, and M. Ibrahim, in 2025 28TH INTERNATIONAL CONFERENCE ON ELECTRICAL MACHINES AND SYSTEMS, ICEMS, Busan, Republic of Korea, 2025, pp. 49–54.

Additively Manufactured Ferrite Permanent Magnet Rotor with 3D Flux for Efficient Utilization of the Overhang Volume and Enhanced Performance

A. M. Ajamloo, H.Tiismus, A. Kallaste,M. N. Ibrahim and P. Sergeant,” IEEE Transactions on Transportation Electrification, pp. 1–13, 2026.”

Design for recycling : prototyping a rib-less interior permanent magnet rotor with enhanced disassembly

A. Mohammadi Ajamloo, V. Van de Peer, M. Ibrahim, and P. Sergeant,” IEEE TRANSACTIONS ON MAGNETICS, 2026”

Static eccentricity effect on no-load performance of FSCW PM machines with series and parallel windings

3- A. Mohammadi Ajamloo, M. Ibrahim, and P. Sergeant, in 12th International Conference on Power Electronics, Machines and Drives (PEMD 2023), Brussels, Belgium, 2023, pp. 291–298